ACCEPTING ORDERS

The Features:

• Vcap ODAM coupling caps

• The small pF caps are NPO C0G Types - 2 KEMET (390pF @ 1000V) and 2 KEMET (82pf @ 630V) 

• Amtrans AMRG carbon film resistors, selected to provide a warm, rich and lifelike sound.

• "Black Dragon" driver board with the original Dynaco 6GH8A circuit. Tubes 6U8A and 6EA8 can also be used.

• Belton gold contact tube sockets for the driver tubes.

• The filter capacitor is hand polished to a nice shine, it is a Dynakit 30/20/20/20uF quad cap, rated for 525 volts.

• Standard bias circuit using my modernized PCB based bias supply.

• Diodes installed at the rectifier socket to prevent reverse current "flashback".

• Stranded wiring throughout using only Kester Eutectic solder.

• Output impedance is set up for 4Ω, 8Ω and 16Ω ohms. 

• The output terminals are barrier block types.

• The Stereo / Mono switch is fully functional.

• Gold RCA upgraded inputs.

• Large Rubber Feet by Penn Elcom.

• The Brown steel cage is also included.

• Manuals and diagrams with setup guide included.

Careful consideration is given when choosing components for the amp that will contribute to, support, and reveal the beautiful details and amazing sonic characteristics of vacuum tubes. Even order harmonics are favorable to the western musical scale and are more pleasing to the ear than the harsh and fatiguing odd order harmonics generated with solid state. 

About the Dynakit Stereo 70:

The Dynakit / Dynaco ST-70 is the quintessential "must have" tube amplifier - and this one's on a much higher level. It is a true dichotomy of sophistication and simplicity, acting together to create a harmonious musical experience far above expectation. It's like a sonic spa.

This classic amp is special, it sounds absolutely stunning, powerful and clear with holographic realism. It will also be a beautiful centerpiece for your audio system. This amp literally puts you right at the performance, enjoy your show.

The classic push-pull design of the ST-70 is a proven success. If you have not had the pleasure to hear a Dynaco 70 built right, with all new high quality components, then you simply cannot hold a fair opinion of the capabilities and enjoyable listening experience this amp offers. The Dynaco 70 is, and was always very good, but was subject to being poorly assembled by inexperienced builders, many years ago. These countless "bad" examples turn up for sale in various places and unwary buyers then voice opinions of the Dynaco 70 based on units that not only desperately need service, are loaded with antiquated, deteriorated and out of spec parts and poor soldering, some builds were never quite right from the beginning. Even the factory wired models offer little advantage, other than they were likely wired correctly, when they were first sold. After 50 plus years of use, abuse and long term storage, those worn and aged components cannot provide enjoyable, safe or reliable operation. 

I have always found the stock circuit to sound the best, they didn't sell over 350,000 of these because they sounded mediocre, this is a rather conspicuous fact. Consider this, if you will. If any of the past, present or modified and alternative circuits were really better, wouldn't those have then, or currently dominate the market? Imitation is the highest form of flattery, but when you install a VTA (tubes 4 hifi), Curcio Audio, Triode Electronics or any other driver circuit, the amplifier is no longer a Dynaco. Mate this original circuit amp with a quality preamp and some high efficiency speakers and you will be amazed. At 35 watts per channel, it will effortlessly drive even large speakers, with realism and clarity, to listening levels far beyond what most folks would consider comfortable. 

Want to hear what actual owners have to say? Click here to read some of their reviews.

Powered by a massive "made in USA" Dynakit PA-060 (current production) power transformer, which is wound and designed for 120 volt operation. This current production Dynakit transformer does not require a step down transformer. It is designed to operate on today's higher voltages. These new Dynakit transformers were reverse engineered from the original designs using modern technologies, materials and superior insulations. The increased lamination stack allows it to run cooler and provide better regulation. These are super high quality transformers that meet and exceed every aspect of the originals. Modern advancements in materials, combined with traditional methods and better technologies used in their production results in absolutely an superb transformer that produces improved sonics and provides cleaner power. 

The new ,current production, Dynakit A470 output transformers are also greatly improved, and made in the USA, like the power transformer. These modern output transformers are interleaved/layer-wound and incorporate the high quality M-6 grain oriented laminations like the original design. These use better quality wire with better insulation, the primary is wound the same as the original A470 using the same number of turns on the same number of sections. These are made using the same patented Dynaco winding method, and made on the same core size and material type as the originals. These transformers match or exceed the frequency ranges of the originals. These transformers are in one word, exceptional.

I only use genuine USA made Dynakit C-354 filter chokes. These new production chokes are fully encased in a metal housing for excellent shielding and won't leak and goop up your chassis like other brands will.

The bias supply is specially designed, an upgrade which puts a PCB in place of the old 7 lug terminal strip. This is the exact same circuit, just re-designed for using modern components to provide a quieter and more stable operation. 

The RCA inputs I use are gold plated for improved contact and corrosion resistance, the inputs are spaced slightly wider apart, making more room for larger sized connectors.

Carefully and expertly wired by hand using only Kester 63/37 eutectic solder for superb connections. 20 AWG and 22 AWG stranded wire throughout.

Safety diodes are installed on the rectifier tube socket.

An "anti click" capacitor is installed on the power switch for a pop/thump free power on and off.

Photos are of the actual amplifier being offered.

The gleaming trophy quality chassis is from Dynakit made with mirror polished stainless steel (non magnetic), it is just a work of art.

The amp sits proudly on 4 oversized rubber feet for improved chassis ventilation and has a great looking stance.

This is a high quality, custom built, hand assembled amplifier you'll be proud to own and enjoy listening to, it sounds fantastic. It's a real eye catcher that also performs beyond expectation.

Before using the amplifier, check and adjust the bias. You will need a voltmeter capable of reading DC Volts / DC Millivolts. Full instructions with diagrams are included. This is a very simple and straightforward procedure and part of owning virtually any tube amplifier. AC voltage can actually vary from outlet to outlet so set the bias using the outlet you intend on operating the unit on / from. Anytime you relocate the amplifier or change tubes you need to check the bias and adjust it for a correct setting. Failure to keep bias set properly can result in premature tube failures and other issues. You should check the bias periodically, about every 80 to 100 hours of use.

Manuals, instructions, diagrams are all printed and included. Email and phone support is provided as needed.

ST-70 DIMENSIONS:

• 13" wide x 9 1/2" deep x 6 1/2" tall * height will vary slightly depending on type of feet (depth measurements are without cables attached)

• Unboxed weight is approximately 35 lbs

Dynaco 70 for sale, Dynaco 35 for sale, Dynaco PAS for sale, Dynakit for sale, ST-70, ST-70, PAS, PAS2, PAS3, PAS3X, Dynaco Tube Stereo, Dynaco Amplifier, Dynaco Preamplifier, Dynaco Tube, Dynakit Tube